Not sure where wood glue fits into that, all i know is that one takes a while because it requires interaction with the molecules that make it hard, i did say i was using wood glue right?
also, bravatoom, you are one master stock builder.
Search found 394 matches
- Thu Apr 30, 2015 5:44 pm
- Forum: General How-To & Discussion
- Topic: laminating / stock building.(LOG)
- Replies: 12
- Views: 8856
- Mon Apr 27, 2015 5:56 pm
- Forum: General How-To & Discussion
- Topic: laminating / stock building.(LOG)
- Replies: 12
- Views: 8856
Re: laminating / stock building.(LOG)
I was trying not to double post, sorry for the delay. the next thing i like to do after drafting is to create a pattern that is good to lay out on the wood. I like a paper one because i can cut through the paper, so i can leave an edge away from the line that is 1/4" to 3/8" from the pencil lines. T...
- Sat Apr 25, 2015 2:32 pm
- Forum: Ammo & Parts
- Topic: 3D printing darts
- Replies: 6
- Views: 5955
Re: 3D printing darts
For the smaller .177 darts a little sand paper and maybe a cotton wad would help.
- Sat Apr 25, 2015 2:28 pm
- Forum: Pneumatic Cannons
- Topic: Access to lathe...what should I make?
- Replies: 3
- Views: 4822
Re: Access to lathe...what should I make?
why not spring load the trigger? it may make it a little larger and more complicated, but it would push the valve open pretty fast helping achieve greater accuracy. also i agree with gippeto, make some bullet molds while you can. Hot glue bullets seem to be popular(also weighting the tip is possible...
- Thu Apr 23, 2015 8:31 pm
- Forum: Pneumatic Cannons
- Topic: Coaxial Piston Cannon
- Replies: 2
- Views: 2198
Re: Coaxial Piston Cannon
I think you created a very expensive air compressor.
- Thu Apr 23, 2015 4:28 pm
- Forum: General How-To & Discussion
- Topic: laminating / stock building.(LOG)
- Replies: 12
- Views: 8856
laminating / stock building.(LOG) Pt2
No problem man, its ok, I kinda am a spudfiles failure. I just was going in order and was pressed for time. back on topic: design your stock AROUND YOUR *GUN! if you design your stock first, your gun becomes much harder and time consuming. Also borrowing ideas from other guns will help you create yo...
- Thu Apr 23, 2015 3:37 pm
- Forum: Off-Topic Hobbies
- Topic: Laser tripwire circuit
- Replies: 12
- Views: 10718
Re: Laser tripwire circuit
ok, just wondering, but if i stuck a battery a motion detector(from a porch light), and a small motor to act as a trigger inline would it work as a motion sensing claymore/mockexplosive? i do not get a single word of what you guys are saying, sorry XD. im just wonding if that would be the same effec...
- Thu Apr 23, 2015 3:18 pm
- Forum: General How-To & Discussion
- Topic: laminating / stock building.(LOG)
- Replies: 12
- Views: 8856
Re: laminating / stock building.(LOG)
image.jpg Here cammy I fixed it, it is a log now. I've also built a couple of stocks before for airsoft guns, but I broke them so I threw them away. Here is the stock I'm making with the damp paper towel on the grain to check it, sorry I couldn't really do that while it was in the vice when I start...
- Wed Apr 22, 2015 7:00 pm
- Forum: General How-To & Discussion
- Topic: laminating / stock building.(LOG)
- Replies: 12
- Views: 8856
Re: laminating / stock building.
I'm building one right now, I just had to go to bed, it is for a .22 rifle. I'm going to do the next section of the how to soon.
- Wed Apr 22, 2015 4:23 pm
- Forum: BB, Airsoft, and Pellet Guns
- Topic: I do not want to get blown up.
- Replies: 13
- Views: 7545
Re: I do not want to get blown up.
I have bad teachers for that part, usually they don't even know the homework they are gonna give. And usually chores around the house take time.
- Tue Apr 21, 2015 11:28 pm
- Forum: Pneumatic Cannons
- Topic: 20mm Airsoft Howitzer
- Replies: 9
- Views: 12195
Re: 20mm Airsoft Howitzer
I vote exploding shells, like rounds that when they contact something they create a spray of bbs. Pneumatically
- Tue Apr 21, 2015 11:26 pm
- Forum: Pneumatic Cannons
- Topic: So I suck at casting my line.....
- Replies: 1
- Views: 1748
Re: So I suck at casting my line.....
Well, if you think about it, a large piston valve launcher is an option, bit you would probably have to Cary either a compressor or an air source (co2 cartridge or a container profiled with air, or a container connected to a compressor, effectively making a low volume compressor.)
- Tue Apr 21, 2015 8:44 pm
- Forum: General How-To & Discussion
- Topic: laminating / stock building.(LOG)
- Replies: 12
- Views: 8856
laminating / stock building.(LOG)
I started building a stock, because I want to be a gunsmith when I get older. I figured showing how to make the stock would be useful for people on here because airguns sometimes need a good stock.( Im sorry I do not have pictures of the laminating of the stock, I forgot at that time.) To start, you...
- Tue Apr 21, 2015 8:19 pm
- Forum: BB, Airsoft, and Pellet Guns
- Topic: I do not want to get blown up.
- Replies: 13
- Views: 7545
Re: I do not want to get blown up.
velocity, please tell me that is a joke. it just i have no money, i literally owe my dad like 20 bucks. i also have a forge that im building (firebricks is the $20). unfortunately since it is near the end of the year, all the teachers put on a huge amount of work, like this week we finish all the st...
- Fri Apr 17, 2015 5:26 pm
- Forum: BB, Airsoft, and Pellet Guns
- Topic: I do not want to get blown up.
- Replies: 13
- Views: 7545
Re: I do not want to get blown up.
Oh, my brain died on me there, sorry. I'll ask for it when I get done with my .22 I got, because for some darn reason I can get guns easier than air gun stuff, though I did get a fire extinguisher. Soon gippeto, soon. I'm gonna play with this qev first. I'll take you up on that offer soon, when I ha...