Search found 15 matches
- Sun Jul 01, 2007 12:06 pm
- Forum: Ammo & Parts
- Topic: rubber bullets
- Replies: 17
- Views: 4613
- Sun Jul 01, 2007 11:31 am
- Forum: Pneumatic Cannons
- Topic: is there a way to make a old propane tank into a air tank
- Replies: 25
- Views: 4071
lets see, start with a multi port fitting(tee fitting) then in one hole thread in a tank valve(schrader or presta), and in the other, a valve of sorts, and a hose barb, then get some high pressure hose, and some hose clamps, then another hose barb, and a locking foot ball air chuck. assemble and thr...
- Sun Jul 01, 2007 11:20 am
- Forum: Ammo & Parts
- Topic: rubber bullets
- Replies: 17
- Views: 4613
well, the lead melts at just under 350*C, and dosen't give off toxic vapors untill around 400*C so mostly i just set the oven and leave it untill melted, but with rubber the smoke point, or for that matter the ignition point is much lower and i dont want another "episode" :oops: i also considered a ...
- Sun Jul 01, 2007 10:58 am
- Forum: Pneumatic Cannons
- Topic: is there a way to make a old propane tank into a air tank
- Replies: 25
- Views: 4071
- Sun Jul 01, 2007 10:56 am
- Forum: Ammo & Parts
- Topic: rubber bullets
- Replies: 17
- Views: 4613
rubber bullets
hey evrbody, had me a idea. i have very successfully been shooting 1" rubber balls, and at the same time been experimenting with lead casting. now how difficult do you think it would be to, say, cast a rubber 1" bullet shape from melted rubber, also at what temp would a standard super ball melt and ...
- Fri Jun 29, 2007 5:43 pm
- Forum: Ammo & Parts
- Topic: pvc cement question, kinda
- Replies: 11
- Views: 4487
- Thu Jun 28, 2007 6:53 pm
- Forum: Ammo & Parts
- Topic: pvc cement question, kinda
- Replies: 11
- Views: 4487
on a previous cannon i tried some epoxy for a leak and couldn't get the epoxy to actually stick to the pvc, i re-read the directions and it was recomended for pvc, but like i said it just flaked off after a thorough cleaning, drying, and a 24 hour dry\cure time. thanx but it looks like i'll just hav...
- Thu Jun 28, 2007 5:56 pm
- Forum: Ammo & Parts
- Topic: pvc cement question, kinda
- Replies: 11
- Views: 4487
thanx for the quick replies guys, yes all parts were sch 40 pressure rated pvc, and i used purple primer and glue for pvc from a company called oatey. The parts in question were a 4 inch diameter pipe and a reducer fitting. Does the glue ever go bad, because it occurs to me that the can in question ...
- Thu Jun 28, 2007 5:37 pm
- Forum: Ammo & Parts
- Topic: pvc cement question, kinda
- Replies: 11
- Views: 4487
pvc cement question, kinda
Hi all, my question is, i used primer and glue to create a pneumatic chamber, and when i pressure tested it, the seal between the fitting and the pipe sprung a leak, why? I followed all the directions given (what with the wet primer and quarter turns and all) and, is there anything i can do, short o...
- Fri Jun 22, 2007 7:02 pm
- Forum: Ammo & Parts
- Topic: Ammo Ideas
- Replies: 359
- Views: 4886146
- Thu Jun 14, 2007 5:51 pm
- Forum: General How-To & Discussion
- Topic: What state u in?
- Replies: 155
- Views: 49757
- Wed May 23, 2007 8:05 pm
- Forum: Off-Topic Hobbies
- Topic: The Official: "Things that piss you off" Thread!!
- Replies: 1319
- Views: 222950
- Sat May 19, 2007 4:28 pm
- Forum: Off-Topic Hobbies
- Topic: Americans about the Netherlands
- Replies: 57
- Views: 8840
- Sat May 19, 2007 4:18 pm
- Forum: Hybrid Cannons
- Topic: Taternator II SUPERSONIC
- Replies: 15
- Views: 6146
- Tue May 15, 2007 7:45 pm
- Forum: Off-Topic Hobbies
- Topic: How old are you?
- Replies: 168
- Views: 30328