Trebuchet
- paaiyan
- First Sergeant
- Posts: 2140
- Joined: Wed Dec 27, 2006 10:03 pm
- Location: Central Oklahoma
- Been thanked: 1 time
I've been planning on building a trebuchet for a while now, but I need some 4x4 posts. Anyone know about how much they cost? I'm gonna build it pretty big, and I want it sturdy.
"Who ever said the pen was mightier than the sword, obviously, never encountered automatic weapons."
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
well you can buy them at 8 feet or at 12 feet. i think 6 foot ones are about $10 (give or take a few dollers, it depends where you live). i dont know how much 12 foot ones are.
the easyest way to find out is to go to home depot and look in the wood section.
the easyest way to find out is to go to home depot and look in the wood section.
"physics, gravity, and law enforcement are the only things that prevent me from operating at my full potential" - not sure, but i like the quote
you know you are not an engineer if you have to remind yourself "left loosy righty tighty"
you know you are not an engineer if you have to remind yourself "left loosy righty tighty"
- mark.f
- Sergeant Major 4
- Posts: 3635
- Joined: Sat May 06, 2006 11:18 am
- Location: The Big Steezy
- Has thanked: 57 times
- Been thanked: 57 times
- Contact:
Are these going to be quick-creted into the ground, like if you were building a deck foundation? Or are they just going to make a base you could move around?
Hi is right. They are not that much. In South GA they run about 8 to 10 dollars.
- paaiyan
- First Sergeant
- Posts: 2140
- Joined: Wed Dec 27, 2006 10:03 pm
- Location: Central Oklahoma
- Been thanked: 1 time
I'm going to make a sturdy base, then cross-brace it just in case. I'm not going to use screw to hold it together, I'm going to use bolts and nuts so I can label the parts, disassemble it, then reassemble it on-site. I'll probably stake it down in a couple places once assembled. I'd rather be able to tear it down for transport, because it's going to be big. No cop would pull me over for having lumber in the truck, but I bet they would if I had an 8 foot tall trebuchet in the back.
"Who ever said the pen was mightier than the sword, obviously, never encountered automatic weapons."
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
- paaiyan
- First Sergeant
- Posts: 2140
- Joined: Wed Dec 27, 2006 10:03 pm
- Location: Central Oklahoma
- Been thanked: 1 time
OK, sorry for the double, but I have another question, and I kind of want to make sure the topic stays in the recents so I can get an answer. I just realized that I haven't got a clue what I'm going to use to support the arm. Like I said, this thing is going to be big, 300-400 pound counterweight, and probably between 75-100 pounds for the arm itself. Anyone got any ideas what I could use as an axle for the thing?
"Who ever said the pen was mightier than the sword, obviously, never encountered automatic weapons."
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
- rednecktatertosser
- Corporal
- Posts: 590
- Joined: Tue May 22, 2007 7:52 pm
go to a junkyard, and look for an old rear wheel drive car axle, thats probably your best bet.
"When you tell some body something, it depends on which part of these United States your standing in, as to how dumb you sound."
-Burt Reynolds as: Bo "Bandit" Darville
-Burt Reynolds as: Bo "Bandit" Darville
- paaiyan
- First Sergeant
- Posts: 2140
- Joined: Wed Dec 27, 2006 10:03 pm
- Location: Central Oklahoma
- Been thanked: 1 time
You know about how much that would be? I'm trying to not spend too much on this thing. For now my idea is a steel pipe with wooden dowels jammed down in it and some concrete ti fill in the space.
"Who ever said the pen was mightier than the sword, obviously, never encountered automatic weapons."
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
- jimmy101
- Sergeant Major
- Posts: 3199
- Joined: Wed Mar 28, 2007 9:48 am
- Location: Greenwood, Indiana
- Has thanked: 5 times
- Been thanked: 17 times
- Contact:
Paaiyan: You might want to consider putting this thing on wheels, even if you plan on taking it apart for transporting.
1. A treb will usually throw farther if it is on wheels.
2. Wheels significantly decrease the stresses on the treb when it is fired.
1. A treb will usually throw farther if it is on wheels.
2. Wheels significantly decrease the stresses on the treb when it is fired.
- paaiyan
- First Sergeant
- Posts: 2140
- Joined: Wed Dec 27, 2006 10:03 pm
- Location: Central Oklahoma
- Been thanked: 1 time
I was thinking about doing that jimmy. I can always do that later too, my concern right now is my axle, I don't want to shell out the money for the axle from a car, but I want it to be strong.My plan at the moment is a steel pipe, 2 inch perhaps, with wood dowels jammed in it, and if there's any space left, I'll fill it with rebar.
"Who ever said the pen was mightier than the sword, obviously, never encountered automatic weapons."
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-
- Private 4
- Posts: 96
- Joined: Sat Oct 21, 2006 8:55 pm
I have a few points to add, and a few questions.
1. What do you plan on using for weights?
2. My friend and I built one out of fough cut 2X10's on my farm, the base is 8' X 4' and the arm is 12' long. we have 400 pounds of Ford tractor weights on it and they are NOT enough, not even close, so if you plan on building one that big, make sure you have enough weight.
3. Also, if you plan on making one with wheels, make sure you use a fixed counterweight, or if no wheels, you HAVE to have a swinging counterweight. I hope you've done your research.
4. What are you going to use for a trigger?
5. How do you plan on pulling the arm down?
1. What do you plan on using for weights?
2. My friend and I built one out of fough cut 2X10's on my farm, the base is 8' X 4' and the arm is 12' long. we have 400 pounds of Ford tractor weights on it and they are NOT enough, not even close, so if you plan on building one that big, make sure you have enough weight.
3. Also, if you plan on making one with wheels, make sure you use a fixed counterweight, or if no wheels, you HAVE to have a swinging counterweight. I hope you've done your research.
4. What are you going to use for a trigger?
5. How do you plan on pulling the arm down?
- rednecktatertosser
- Corporal
- Posts: 590
- Joined: Tue May 22, 2007 7:52 pm
i would advise using concrete for filling the pipe,
alternatively, if you found a pretty hefty branch, 2.5 to 3" in diameter, that would work pretty damn well.
alternatively, if you found a pretty hefty branch, 2.5 to 3" in diameter, that would work pretty damn well.
"When you tell some body something, it depends on which part of these United States your standing in, as to how dumb you sound."
-Burt Reynolds as: Bo "Bandit" Darville
-Burt Reynolds as: Bo "Bandit" Darville
- paaiyan
- First Sergeant
- Posts: 2140
- Joined: Wed Dec 27, 2006 10:03 pm
- Location: Central Oklahoma
- Been thanked: 1 time
1. concrete.
2. 10' arm, at least 400 pounds of weight, more if we decide we need it.
3. no wheels, hinged weight.
4. probably i-hooks and a pin. But upon suggestion, for the sake of the contest video, im going to tie the rope off so it wont whip around and cut it with a sword, because I'm cool like that and I have one.
5. rope and pulleys, most likely if i cant get it down, ill hook it up to my truck and pull it that way.
2. 10' arm, at least 400 pounds of weight, more if we decide we need it.
3. no wheels, hinged weight.
4. probably i-hooks and a pin. But upon suggestion, for the sake of the contest video, im going to tie the rope off so it wont whip around and cut it with a sword, because I'm cool like that and I have one.
5. rope and pulleys, most likely if i cant get it down, ill hook it up to my truck and pull it that way.
"Who ever said the pen was mightier than the sword, obviously, never encountered automatic weapons."
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-
- Private 4
- Posts: 96
- Joined: Sat Oct 21, 2006 8:55 pm
What are you going to use for weight?
and have you seen this website? http://members.iinet.net.au/~rmine/Grey ... html#frank
I can send or post pictures if you want, but I'd have to take them first
and have you seen this website? http://members.iinet.net.au/~rmine/Grey ... html#frank
I can send or post pictures if you want, but I'd have to take them first
- paaiyan
- First Sergeant
- Posts: 2140
- Joined: Wed Dec 27, 2006 10:03 pm
- Location: Central Oklahoma
- Been thanked: 1 time
I said I was using concrete.
And that was a bad link.
And that was a bad link.
"Who ever said the pen was mightier than the sword, obviously, never encountered automatic weapons."
-General Douglass MacArthur
Read my dog's blog - Life of Kilo
-General Douglass MacArthur
Read my dog's blog - Life of Kilo