C.A.M.O "RIFLE"

[Pyro Ninja]

Camo.Anti.material."O" "rifle"
Its not a rifle perse, but I recon it looks the part
Specs
Chamber- 25mm Pn18 pvc pipe (pressure rated)
Valve- madded 25mm sprinkler valve
Barrel- 20mm poly pipe
ammo- marbles
I know there is a little bit of dead space between the valve and the barrel and the blowgun and the valve, but I'm happy with the power and comfortability I'm getting.
R UA RED DA

Ok heres some Picture-
__________________
Before I painted it camo (matt black)

__________________
Being painted.

__________________
Snub barrel, kind of like a shot gun.

__________________
Long "rifle" barrel.

__________________
Basking in the sun

__________________
Video- Marble from about 5m away. (10 points for the one you can figure out the problem with the video)

Another video- cordial bottle full of water shot with marble a 100 psi.

There you go, comments welcome
Any suggestions to finish the acronym

[MrCrowley]

Very nice, though I think that camo isn't doing any good with a gloss coating

[jackssmirkingrevenge]

I know there is a little bit of dead space between the valve and the barrel and the blowgun and the valve, but I'm happy with the power and comfortability I'm getting.

... as well as inventing new words

Still, nice effort, and on with the damage pics/vids!

[Pyro Ninja]

About the gloss, It wasn't glossy until I sprayed it with a clear coat to protect the paint, It looked nicer without the gloss
Damage pics will come soon.

[MrCrowley]

I know what you mean, I found it also darkens the paintjob quite a bit too
I don't bother with gloss anymore, I just wait a week for the paint to fully cure, or just be really, really careful with it.

[experament-u2]

hmm seams so familiar for some reason
nice job chap i think you should chuck a support between the barrel and chamber it will feel so much better

[Davidvaini]

helpful tip on when the clearcoat adds glossiness to your paint job... apply your common color... then do a layer of clear coat and then do another layer of your common color or camo... this way if your top surface paint gets scratched you wont really nottice it because there will be a layer of clearcoat and under that your common color... you can do this multiple times for more coats.

[Pyro Ninja]

I just wait a week for the paint to fully cure, or just be really, really careful with it.

I waited atleast a week, aswell as being really, really careful with it, and the paint still gets scratched off. Crappy, cheap spray paint

i think you should chuck a support between the barrel and chamber it will feel so much better

Yeah, Im planning that

[XxtriviumxX]

more like C.A.M.O "Smoothbore" tis quite nice... both the camo and black paint looked equally good... though as Crowley said the gloss isnt doing any good for the camo, kinda harder to see... there for the black was better lol

[Pyro Ninja]

A little Video is up now.
The shot is from about 5 meters away with a marble at 100psi, who can figure the problem out?

I will also acknowledge that the design is based of "experament_u2"s "reaper rifle" Good design

[sniperjosh]

Hehe, nice gun.

The material list and valve let me know your from australia Good to see more aussies

What marbles do you shoot?? (diameter, where do you get them, how much)

well done on the paint job

[bigbob12345]

Very nice gun
I like the glossy camo, it looks good. But the blue tape wrapped around the blowgun kinda ruins the look a little. I would recommend replacing it with hose clamps.

[Jared Haehnel]

Agreed...nice gun...replace the blue tape with electrical tape... 8)

[Fnord]

Any suggestions to finish the acronym?

http://www.jasonblogs.com/acreator/index.php

[Pyro Ninja]

What marbles do you shoot?? (diameter, where do you get them, how much)

The marbles I use are just cheap cat eye ones, they are 4 grams each and only costed $1.00 for 101 (the 1 is the large one).
Although they don't fit perfectly in the barrel, with a bit of tissue as wadding, they shoot pretty well.

Has anybody worked out the problem with the first video?