Home made amazing mini gun for airsoft *must do*
Posted: Tue Aug 23, 2011 11:39 pm
Hey guys 
This is a supply list/tutorial on how to make a airsoft mini gun that I have named nightshade it fires probably 100 Bbs a second and had roughly 400 to 450 fps supply's needed
Are 2, 3 foot sections of 3 inch PVC pipe and four 3 inch end caps air tight tubes like gas line that is 3/8 in of an inch in diameter u need about 6 feet of that. You need an airsoft barrel just
Strip it or use tubing u need a section of an inch pipe for the outer barrel (5 inches shorter
Than inner barrel 3 foot section of 2 inch PVC cut in half 4 2 inch end caps. Some sort of easy push air tight valve( not sure of proper term) and about 5 or six metal sections to connect your tubing and enough hose clamps to fit sound that and 2 hose clamps that fit around your gun to secure the barrel and pressur chambers and finally a tire valve take the two three foot three inch PVC pipes and place and glue the end caps after inserting the tire thing that the air enters into on the left end cap on the top then drill a hole slighty smaller than your metal connecters and screw them in the tube should be from the bottom end caps connecting the two chambers so the air can travel through both thus getting longer
Firing time. Then we go to the smaller chambers take two end caps and glue them onto one end of both 1.5 feet 2 inch chambers then connect the backs with elbows that fit unto each other. Drill a hole in the elbow that slides over and connect a tube leading from the back
Chamber to them select your
Own placement to your desire. So that the air can run through all 4
Chambers. Now for the barrel use 1 inch pipe all the way down your barrel and place a end cap make
Sure the back has about 3 inches of barrel sticking out then take
An end cap and run the barrel through now u should have about 2 inches sticking out then take a 1 inch section about 5 inches Long for your cloud chamber and put an end cap on one end drill a
Hole for your barrel and slide on your barrel should be flush with the end cap
Inside and then on the back have abscess
So you can fill your cloud chamber with Bbs connect your cloud chamber with the quick air release and a tube running to your 2 inch chamber and tighten with hose clamps and then u can decorate to your hearts desire fill up with air and boom go skirmish but bring a bike pump with you or your outa luck thanks for reading
52ndbattalionairsoft
I was born withs spuds in my veins[quote][/quote]
This is a supply list/tutorial on how to make a airsoft mini gun that I have named nightshade it fires probably 100 Bbs a second and had roughly 400 to 450 fps supply's neededAre 2, 3 foot sections of 3 inch PVC pipe and four 3 inch end caps air tight tubes like gas line that is 3/8 in of an inch in diameter u need about 6 feet of that. You need an airsoft barrel just
Strip it or use tubing u need a section of an inch pipe for the outer barrel (5 inches shorter
Than inner barrel 3 foot section of 2 inch PVC cut in half 4 2 inch end caps. Some sort of easy push air tight valve( not sure of proper term) and about 5 or six metal sections to connect your tubing and enough hose clamps to fit sound that and 2 hose clamps that fit around your gun to secure the barrel and pressur chambers and finally a tire valve take the two three foot three inch PVC pipes and place and glue the end caps after inserting the tire thing that the air enters into on the left end cap on the top then drill a hole slighty smaller than your metal connecters and screw them in the tube should be from the bottom end caps connecting the two chambers so the air can travel through both thus getting longer
Firing time. Then we go to the smaller chambers take two end caps and glue them onto one end of both 1.5 feet 2 inch chambers then connect the backs with elbows that fit unto each other. Drill a hole in the elbow that slides over and connect a tube leading from the back
Chamber to them select your
Own placement to your desire. So that the air can run through all 4
Chambers. Now for the barrel use 1 inch pipe all the way down your barrel and place a end cap make
Sure the back has about 3 inches of barrel sticking out then take
An end cap and run the barrel through now u should have about 2 inches sticking out then take a 1 inch section about 5 inches Long for your cloud chamber and put an end cap on one end drill a
Hole for your barrel and slide on your barrel should be flush with the end cap
Inside and then on the back have abscess
So you can fill your cloud chamber with Bbs connect your cloud chamber with the quick air release and a tube running to your 2 inch chamber and tighten with hose clamps and then u can decorate to your hearts desire fill up with air and boom go skirmish but bring a bike pump with you or your outa luck thanks for reading
52ndbattalionairsoft
I was born withs spuds in my veins[quote][/quote]