"In the world of spuds today"

[qwerty]

Good to see you decided to go down the hybrid route. You'll be quite happy with the power.

And i might have allready cocked it up
I have epoxyed it all together but have forgotten the spark gaps
Anyway, as i have no access to the schrader anymore, how should i go about making a spark gap. I was thinking, just use some screws with a gap of about 1.5mm and epoxy them in. But then i thought, wouldn't i get a shock instead of the spark jumping? So i am thinking of wrapping the whole thing in electrical tape. Would that work?

EDIT: Nevermind, problem solved More epoxy is curing. I should get some results tomorrow.

[saefroch]

Good to see there's a lot of builds coming in, and hybrid to boot!

I'll hopefully be doing some drill press work to start making my piston tonight.

In the two weeks that I've had my tubes of epoxy, I've managed to fix three things around the house with it. Sure is some awesome stuff.
And yes, it's amazing for making things for the girlfriend.

[jackssmirkingrevenge]

moar hybrids yay!

In the two weeks that I've had my tubes of epoxy, I've managed to fix three things around the house with it.

Welcome to the dark side

And yes, it's amazing for making things for the girlfriend.

Waste of high spec adhesive.

[saefroch]

Waste of high spec adhesive.

Only when you have to pay for it.

[saefroch]

ITWOST: I almost got a drill bit stuck in epoxy, trying to drill through it. I was attempting to fill in the rather large scratches on the inside of the spacer I'm using for my piston, but upon drilling out the epoxy, there were still significant ridges... help?

Is there significant DDT danger for an air-propane hybrid chamber 28" x .5"?

[mark.f]

You could mitigate it with multiple ignition points... as far as a definitive geometry which would induce DDT, I can't tell you exactly, but propane/air isn't the best candidate for the transition.

[Technician1002]

When drilling epoxy, it is important to use low speed. Epoxy expands as it heats. This causes expansion into the drill bit. When cooled, the spots that was hot are now grooves. Use a sharp new bit. A dinged up bit will leave grooves.

[Zeus]

Well I've got a syringe now, fueling math is done, I just need to iron out the bugs in my ignition circuit and I'll have a 15X pistol hybrid.

[jackssmirkingrevenge]

When drilling epoxy, it is important to use low speed. Epoxy expands as it heats. This causes expansion into the drill bit. When cooled, the spots that was hot are now grooves. Use a sharp new bit. A dinged up bit will leave grooves.

Hear hear.

Well I've got a syringe now, fueling math is done, I just need to iron out the bugs in my ignition circuit and I'll have a 15X pistol hybrid

Finally, looking forward to seeing it work

[saefroch]

low speed

Guess I'll be trying again, thanks!

Spark gaps in parallel a good idea?

[qwerty]

ITWOST Qwerty's Micro Hybrid....7X mix.....7 burst disks.... 105psi.....Click.....BOOOM!!!!.....Inspect Target.....Minimal damage.....Missed?......Did you put the pellet in the barrel?.....No....

[jackssmirkingrevenge]

Did you put the pellet in the barrel?.....No....

Happens to all of us sooner or later

[ramses]

If you put the ignition points in parallel, only one will actually see a spark. You must put them in series.

Also, I now have a milling machine.

And I still need advice on a bumper for a 4" toolie valve. I was thinking multiple tennis ball halves.

[saefroch]

My advice: Rubber and strong construction to be able to take the impact.

OOO! Can you model your valve in GGDT for me and take a screenshot of it?

[Technician1002]

And I still need advice on a bumper for a 4" toolie valve. I was thinking multiple tennis ball halves.

Same thing you would use for a 2 inch valve except scale the diameter up for the new larger area and scale the thickness up for the longer travel and higher mass.