i want to make a .177 full auto airgun
-
beastmode986
- Specialist
- Posts: 170
- Joined: Sat Mar 03, 2012 11:13 am
also i am planning on going to lowes or menards tonight . i have 40$ to spend what should i buy for this? im not sure what to use for my air chamber. should i use galvanized pipe?
-
beastmode986
- Specialist
- Posts: 170
- Joined: Sat Mar 03, 2012 11:13 am
-
Gun Freak
- Lieutenant 5
- Posts: 4971
- Joined: Mon Jan 25, 2010 4:38 pm
- Location: Florida
- Been thanked: 8 times
I see... So hook up your co2 tank and slap on a barrel, what are you waiting for? 
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
-
beastmode986
- Specialist
- Posts: 170
- Joined: Sat Mar 03, 2012 11:13 am
one thing how do i add the bolt action? do i put a peice of pipe that fits snug around the barrel and add a screw or something to open it and lock it? also what size pipe fits .22 pellets
and i want to disable the blowback so i dont waste gas. how do i do that i have no clue how the blow back works
what hardware store sells the right tubing
and i want to disable the blowback so i dont waste gas. how do i do that i have no clue how the blow back works
what hardware store sells the right tubing
-
Gun Freak
- Lieutenant 5
- Posts: 4971
- Joined: Mon Jan 25, 2010 4:38 pm
- Location: Florida
- Been thanked: 8 times
Acewhat hardware store sells the right tubing
Sounds like it'd work. Check out the showcase, that's actually a common way of doing it. And, check out page 13 of the Hubb Library, there's a nice example.one thing how do i add the bolt action? do i put a peice of pipe that fits snug around the barrel and add a screw or something to open it and lock it?
also what size pipe fits .22 pellets
Gun Freak from the previous page of this thread wrote:I recommend 22 cal because you can buy a perfect barrel, albeit smoothbore, at the hardware store. 1/4" OD K&S brass has an ID of .222".
OG Anti-Hybrid
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
One man's trash is a true Spudder's treasure!
Golf Ball Cannon "Superna" ■ M16 BBMG ■ Pengun ■ Hammer Valve Airsoft Sniper ■ High Pressure .22 Coax
Holy Shat!
-
beastmode986
- Specialist
- Posts: 170
- Joined: Sat Mar 03, 2012 11:13 am
ok thanks. i went out today and my local ace only sells 1ft sections no bigger so i went to autozone and bought brake line that was just a little tiny bit off 
still i think it will work i aslo bought wood to make the stock. i just epoxied the barrel on and trimmed a few things i am almost done thanks again!
edit: well it appears the barrel is to big:( id wise. so ill need to buy a different one. i also found out that the hammer valve from the tippman dosent work at 150 psi. i filled the co2 tank to 150 psi with some fittings then hooked it directly to the gun via quick connect and if i hit the valve somewhat hard with a hammer it wouldent even push the pellet out of the barrel.
still i think it will work i aslo bought wood to make the stock. i just epoxied the barrel on and trimmed a few things i am almost done thanks again!edit: well it appears the barrel is to big:( id wise. so ill need to buy a different one. i also found out that the hammer valve from the tippman dosent work at 150 psi. i filled the co2 tank to 150 psi with some fittings then hooked it directly to the gun via quick connect and if i hit the valve somewhat hard with a hammer it wouldent even push the pellet out of the barrel.